Bookmark Us
How To Change A Watch Battery
Watch Battery Change Procedure
Star Struck, LLC - StarStruckllc.com
Watch Batteries, Jeweler's Tools & Supplies
How to change a watch battery, this guide as a pdf
How to change a watch battery instructional video
Watch Battery Handling Precautions
Watch Battery Replacement
Changing a watch battery is an easy procedure if you follow these steps.
Always examine the watch before opening the back of the case.
If the watch experienced water damage or if the watch hands
or stem is loose you may need to have it repaired by a professional watchmaker.
If you notice the hands are jumping in multi-second
increments, this is a sign that a battery replacement is necessary.
If you have a pulse tester, use this to determine if the battery is dead
or if the watch needs to be repaired. This will eliminate the need to
unnecessarily open the watch. Always clean the case back before opening the watch.
This will prevent and dirt from entering the watch movement when the back is removed.
A small brush or toothbrush can be used to lightly remove the debris from the watch.
If you have compressed air you can use this to blow the dirt free.
Always use the proper tools to repair your watch.
If the case is a screw back the dirt can easily fall onto the thread and make
closing the watch very difficult.
Then it is important to determine the type of case back that is on the watch.
Once this is determined follow the steps below. Always be careful when removing
the watch back. Most watches have a gasket that prevents water from entering
the case. Always return this to the correct position when you close the watch.
Watch Battery Change #1
In order to change a watch battery, first determine your case back.
SNAP BACK
If the watch looks similar to this, change the watch battery, following these instructions contained in the first section labeled snap back on page 3.
HATCH BACK
If the watch looks similar to this, change the watch battery, following these instructions contained in the first section labeled hatch back on page 5.
SCREW BACK
If the watch looks similar to this, change the watch battery, following these instructions contained in the first section labeled screw back on page 7.
RETAINER RING
If the watch looks similar to this, change the watch battery, following these instructions contained in the first section labeled retainer ring on page 9.
Watch Battery Change, Replacing a Watch Battery, How To Change A Watch Battery, Watch Battery Replacement Steps, Change a Watch Battery Guide, Steps For Changing a Watch Battery, Changing a Watch Battery, How to Change A Watch Battery, Easy Procedure For Watch Battery Changing, Easy to Follow Steps in Changing A Watch Battery, How to Change a Watch Battery?, How To Change a Watch Battery?, How To Change a Watch Battery, How To Change a Watch Battery? Follow This Guide To Change Your Watch Battery, Watch Battery Change, Your Source For Watch Repair Tools, Repair Your Watch and Change Your Battery.
DO'S AND DONT'S
DO
Read and follow these instructions very carefully.
DO
Always use factory fresh Star Struck, LLC watch batteries when performing a watch battery replacement.
DO
Use tools supplied by Star Struck. Listed below are the tools mentioned in this guide:
SST-735 ...... Precision screwdriver set
SST-879 ...... Plastic tweezers
SST-808 ...... Screw holding tweezers
SST-200 ...... Battery tester
SST-9030 .... Watch battery sizer
SST-603 ...... Case wrench/opener
SST-012 ...... Polishing cloth (5x5)
SST-20 ........ Scratch brush
SST-302 ...... Hardwood movement holder
SST-625 ...... Bench Knife
SST-165 ...... Case opener
SST-1205 .... Case knife
SST-905 ...... Case Press
SST-092 ...... Master Jig
SST-91 ........ Case Closing Pliers
SST-BC ....... Battery Storage Cabinet
DON'T
Force any watch parts that do not come apart or move with reasonable ease when these instructions are followed.
SNAP BACK
Tools Needed:
Prying tool, non-metal tweezers, small screwdriver, battery tester, cleaning cloth, screw holding tweezers, watch closing hand press, polishing cloth , all tools are available from
Star Struck, LLC.
STEP 2
Place the watch in the case holding vise. Clamp the watch in the case holding vise by opening the two halves of the block. Place the watch in the middle, and gently release or tighten the two halves so that they hold the watch firmly (2a).
If the watchband does not unbuckle or unclasp, separate the band by pressing down with the pointed tool to remove the spring-loaded pin that connects the band to the clasp or watch (2b).
STEP 3
Remove the back.
Look for the groove between the round back and the watchcase (3a). Gently insert the case knife beneath the lip which is usually opposite the stem or the nine o’clock position. (3b).
Work the knife into the groove between the round back and the watchcase.
Twist the tool to snap off back (3c).
Step 4
Remove the batteries. IMPORTANT:
Before removing batteries, be sure to note which side is up. You’ll have to put the new batteries in exactly the same. In some watches, the batteries are held in by a small metal clip. If so, carefully follow these directions for removing them.
SPRING CLIP: Lift up one end of the metal clip with the fine point tweezers-it will come out. Then, remove the batteries (4a).
SCREW ON CLIP: Remove the screws with the small screwdriver (4b). Be careful not to lose them. Caution: Clip may spring out; maintain pressure or screw may be ejected.
PERMANENT CLIP: Lift the outside edge of the battery out of its compartment with the small screwdriver (4c).
STEP 5
TEST THE BATTERIES.
See the battery tester for operating instructions.
IMPORTANT:
If the watch has two batteries and only one tests “replace”, replace both batteries. If both batteries test “good”, there is something wrong with the watch. Refer to your watchmaker.
STEP 6
Locate replacement batteries.
Read the number on the old battery. Find the same number in the Star Struck watch battery Cross Reference Guide (6a). Choose the corresponding battery listed in the Cross Reference Guide from the Star Struck battery assortment cabinet (6b).
STEP 7
Clean the battery compartment. Check the battery compartment for dirt and remove it. If you find corrosion, refer to your watchmaker.
STEP 8
Install New Batteries. IMPORTANT
Be sure to test the new batteries before installing. For tester settings, follow manufacturer’s instructions. Install the new Star Struck battery(s) with the same side up as the one(s) you replaced. Remember the watch won’t work if the batteries are put in wrong.
SPRING CLIP: Place one end of the spring clip in place and push the other end into its slot (8a).
SCREW-ON CLIP: Place the clip over the new batteries. Hold the screw with the screw holding tweezers to start it in to the hole. Tighten the screw (8b).
STEP 9
Close the watch. IMPORTANT:
If there is a rubber sealing gasket in the back of the watch, make sure it is lined up properly before closing the back. Snap a metal adapter that is slightly smaller than the watch back into the upper jaw of the press. Place the support plate into the bottom of the press and fit a plastic ring adapter large enough to hold the watch into the support plate. Place the watch face down into the plastic ring adapter and press gently on handle until the watch snaps into place.
STEP 10
Clean the watch. Gently wipe the watch to remove any fingerprints or smudges.
STEP 11
Reset the watch. Reset the watch and make sure it is working. In analog watches, if there is no second hand, observe the minute hand through a magnifying glass until you detect movement.
HATCH BACK
Tools Needed:
Tweezers, battery tester, cleaning cloth, polishing cloth, all tools are available from Star Struck, LLC.
STEP 2
Place the watch in the case holding vise. Clamp the watch in the case holding vise by opening the two halves of the block. Place the watch in the middle, and gently release or tighten the two halves so that they hold the watch firmly (2a).
If the watchband does not unbuckle or unclasp, separate the band by pressing down with the pointed tool to remove the spring-loaded pin that connects the band to the clasp or watch (2b).
STEP 3
Remove the Hatches.
Unscrew the hatches counter-clockwise by turning a coin in the slot (3b). Once the hatches are loosened, finish unscrewing and remove with fingers. Be careful not to let the batteries fall out yet.
STEP 4
Remove the batteries. IMPORTANT:
Before you remove the batteries, be sure to note which side is up-you’ll have to put the new batteries in the exact same way. To remove the batteries, simply turn the watch over and they should fall out. If either battery is stuck, gently pry it out.
STEP 5
Test the batteries.
See the battery tester for operating instructions.
IMPORTANT:
If the watch has two batteries and only one tests “replace”, replace both batteries. If both test “good”, there is something wrong with the watch. Refer to your watchmaker.
STEP 6
Locate replacement batteries.
Read the number on the old battery. Find the same number in the Star Struck watch battery Cross Reference Guide. Choose the corresponding battery in the Cross Reference Guide from the Star Struck battery assortment cabinet.
STEP 7
Clean the Battery Compartment .
Check the battery compartment for dirt and remove it. If you find corrosion, refer watch to your watchmaker.
Step 8
Install the New Batteries . IMPORTANT:
Be sure to test new batteries before installing. For tester settings, follow the manufacturer’s instructions. Install the new Star Struck battery(s) with the same side up as the one(s) you replaced (8A). Remember, the watch won’t work if the batteries are put in wrong.
STEP 9
Close the Hatches
Start screwing in the hatches with your finger, then tighten with a coin (9A).
STEP 10
Clean the Watch
Gently wipe the watch to remove any fingerprints or smudges.
STEP 11
Reset the Watch
Reset the watch and make sure it is working. In analog watches, if there is no second hand, observe the minute hand through a magnifying glass until you detect movement.
SCREW BACK
Tools Needed:
Case wrench, non-metal tweezers, small screwdriver, battery tester, cleaning cloth, screw holding tweezers, rubber-tipped opener, polishing cloth, all tools available from Star Struck, LLC.
STEP 2
Place the watch in the case holding vise. Clamp the watch in the case holding vise by opening the two halves of the block. Place the watch in the middle, and gently release or tighten the two halves so that they hold the watch firmly (2a).
If the watchband does not unbuckle or unclasp, separate the band by pressing down with the pointed tool to remove the spring-loaded pin that connects the band to the clasp or watch (2b).
STEP 3
Remove the Back.
Place the rubber-tipped opener in the middle of the watch back (3b). Press firmly and turn counter-clockwise to remove watch back (3c).
STEP 4
Remove the batteries. IMPORTANT:
Before you remove the batteries, be sure to note which side is up. You’ll have to put the new batteries in exactly the same way. In some watches, the batteries are held in by small metal clips. If so, carefully follow these directions for removing the various types of clips:
Spring Clip: Lift up one end of the metal clip with the fine-point tweezers—it will come out. Then remove the batteries (4A).
Screw-On Clip: Remove the screws with the small screwdriver (4B). Be careful not to lose them. Caution: Clip may spring out. Maintain pressure or screw may be ejected.
Permanent Clip: Lift the outside edge of the battery out of its compartment with the small screwdriver (4C).
STEP 5
Test the batteries.
See the battery tester for operating instructions.
IMPORTANT:
If the watch has two batteries and only one tests “replace”, replace both batteries. If both test “good”, there is something wrong with the watch. Refer it to your watchmaker.
STEP 6
Locate replacement batteries.
Read the number on the old battery. Find the same number in the Star Struck Cross Reference Guide. Choose the corresponding battery in the Cross Reference Guide from the Star Struck battery assortment cabinet.
STEP 7
Clean the Battery Compartment .
Check the battery compartment for dirt and remove it. If you find corrosion, refer watch to your watchmaker.
STEP 8
Install the New Batteries . IMPORTANT:
Be sure to test new batteries before installing. For tester settings, follow the manufacturer’s instructions. Install the new Star Struck battery(s) with the same side up as the one(s) you replaced (8A). Remember, the watch won’t work if the batteries are put in wrong.
STEP 9
Close the Hatches
Start screwing in the hatches with your finger, then tighten with a coin (9A).
STEP 10
Clean the Watch
Gently wipe the watch to remove any fingerprints or smudges.
STEP 11
Reset the Watch
Reset the watch and make sure it is working. In analog watches, if there is no second hand, observe the minute hand through a magnifying glass until you detect movement.
RETAINER RING
Tools Needed:
Retainer wrench, non-metal tweezers, small screwdriver, screw-holding tweezers, polishing cloth, all tools are available from: Star Struck, LLC.
STEP 2
Place the watch in the case holding vise. Clamp the watch in the case holding vise by opening the two halves of the block. Place the watch in the middle, and gently release or tighten the two halves so that they hold the watch firmly (2a).
If the watchband does not unbuckle or unclasp, separate the band by pressing down with the pointed tool to remove the spring-loaded pin that connects the band to the clasp or watch (2b).
STEP 3
Remove the Back.
Remove the back. Locate the wrench slots on the back of the watch (3a). Fit the special retainer ring wrench into the slots. Turn counter-clockwise to loosen the retainer ring (3b). When retainer ring is loosened, lift out ring and watch back (3c).
STEP 4
Remove the batteries. IMPORTANT:
Before you remove the batteries, be sure to note which side is up. You’ll have to put the new batteries in exactly the same way. In some watches, the batteries are held in by small metal clips. If so, carefully follow these directions for removing the various types of clips:
Spring Clip: Lift up one end of the metal clip with the fine-point tweezers—it will come out. Then remove the batteries (4A).
Screw-On Clip: Remove the screws with the small screwdriver (4B). Be careful not to lose them. Caution: Clip may spring out. Maintain pressure or screw may be ejected.
Permanent Clip: Lift the outside edge of the battery out of its compartment with the small screwdriver.
STEP 5
Test the batteries.
See the battery tester for operating instructions.
IMPORTANT:
If the watch has two batteries and only one tests “replace”, replace both batteries. If both test “good”, there is something wrong with the watch. Refer it to your watchmaker.
STEP 6
Locate replacement batteries.
Read the number on the old battery. Find the same number in the Star Struck Cross Reference Guide. Choose the corresponding battery in the Cross Reference Guide from the Star Struck battery assortment cabinet.
STEP 7
Clean the Battery Compartment .
Check the battery compartment for dirt and remove it. If you find corrosion, refer watch to your watchmaker.
STEP 8
Install the New Batteries . IMPORTANT:
Be sure to test new batteries before installing. For tester settings, follow the manufacturer’s instructions. Install the new Star Struck battery(s) with the same side up as the one(s) you replaced (8A). Remember, the watch won’t work if the batteries are put in the wrong way.
SPRING CLIP: Place one end of the spring clip in place and firmly push the other end into its slot.
SCREW-ON CLIP: Place the clip over the new batteries. Hold the screw with the screw holding tweezers to start it in the hole. Tighten the screw.
IMPORTANT: If there is a rubber-sealing gasket in the base of the watch, make sure it is lined up properly before closing the back.
STEP 9
Close the Watch
After placing the back on the watch, slip the retaining ring over it and tighten with the special retainer wrench.
STEP 10
Clean the Watch
Gently wipe the watch to remove any fingerprints or smudges.
STEP 11
Reset the Watch
Reset the watch and make sure it is working. In analog watches, if there is no second hand, observe the minute hand through a magnifying glass until you detect movement.
Visit:
http://www.rayovacusa.com
http://www.rayovacwatchbatteries.com
http://www.maxellwatchbatteries.com
http://www.pyramidbattery.com
http://www.vartabattery.com
http://www.vartawatchbatteries.com
http://www.starstruckwatchbatteries.com
http://www.starstruckllc.com
http://www.renatawatchbatteries.com
http://www.maxellbattery.com
http://www.energizerwatchbatteries.com
http://www.howtochangeawatchbattery.com
http://www.selvytusa.com